ASTM D1149-16

本頁面標準信息均來源于網絡收集，或由參與標準制定的供應商提供，只作為參考使用，為確保測試結果的準確性、節省您的時間，如需ASTM D1149-16標準詳細信息或ASTM D1149-16具體測試方法，可與我們技術人員聯系或給我們留言，我們將為您提供相關的技術支持。

 

ASTM D1149 - 16 簡介

ASTM D1149 - 16是關于《臭氧可控環境中橡膠變壞龜裂的標準試驗方法》現行標準版本修訂于2016年，取代原先的ASTM D1149 - 15使用。

1. Scope

1.1 These test methods are used to estimate the effect of exposure, under surface tensile strain conditions, either dynamic or static, in an atmosphere containing specified levels of ozone concentration, expressed as partial pressure (refer to Note 1), on vulcanized rubber, rubber compounds, molded or extruded soft rubber, and other specified materials, or as may be determined empirically. The effect of naturally occurring sunlight or light from artificial sources is excluded.

1.2 Previously published ASTM documents Test Method D518 and Test Methods D3395 have been included in these test methods, D1149, in 2007. Please refer to Note 2.

1.2.1 Test Method D518 and Test Methods D3395 have henceforth been withdrawn and superseded by Test Methods D1149. When Test Methods D1149 is cited, or otherwise referenced, a notation shall be included to this effect. Please refer to section 3.2 for the appropriate references.

1.3 The specified conditions of exposure to ozone in the controlled environments are accelerated in comparison to outdoor exposure. These accelerated ozone test methods may not give results which correlate with outdoor exposure tests or service performance.

1.4 All materials, instruments, or equipment used for the determination of mass, force, dimension, ozone concentration, partial pressure, temperature, velocity, and gas exchange rate shall have direct traceability to the National Institute for Standards and Technology, or other internationally recognized organization parallel in nature.

1.5 The values stated in SI units are to be regarded as standard. The values given in parentheses are for information only. Many of the stated SI units are direct conversions from the .S. Customary System to accommodate the instrumentation, practices, and procedures that existed prior to the Metric Conversion Act of 1975.

1.6 This standard involves hazardous materials, specifically ozone. It may also involve hazardous operations and equipment. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Note 1: A discussion and explanation regarding the measurement of ozone concentrations based upon parts of ozone per unit of air versus partial pressure is provided in Test Methods D4575, specifically Appendices X1 and X2. Test Methods D4575 is also recommended as a source of background information regarding standards involving materials exposed to ozone.

2. Referenced Documents

ASTM Standards

D518 Test Method for Rubber Deterioration--Surface Cracking

D1171 Test Method for Rubber DeteriorationSurface Ozone Cracking Outdoors (Triangular Specimens)

D1349 Practice for Rubber--Standard Conditions for Testing

D3182 Practice for RubberMaterials, Equipment, and Procedures for Mixing Standard Compounds and Preparing Standard Vulcanized Sheets

D3395 Test Methods for Rubber Deterioration--Dynamic Ozone Cracking in a Chamber

D4482 Test Method for Rubber Property--Extension Cycling Fatigue

D4575 Test Methods for Rubber DeteriorationReference and Alternative Method(s) for Determining Ozone Level in Laboratory Test Chambers