現貨東京計器TOKIMEC換向閥DG4V-3-2A-U-H-100

日本株式會社東機美中國銷售代理

現貨東京計器TOKIMEC換向閥DG4V-3-2A-U-H-100

1）空穴產生的噪聲當由于各種原因，空氣被吸入油液中，或者在油液壓力低于大氣壓時，溶解在油液中的部分空氣就會析出形成氣泡，這些氣泡在低壓區時體積較大，當隨油液流到高壓區時，受到壓縮，體積突然變小或氣泡消失；反之，如在高壓區時體積本來較小，而當流到低壓區時，體積突然增大，油中氣泡體積這種急速改變的現象。氣泡體積的突然改變會產生噪聲，又由于這一過程發生在瞬間，將引起局部液壓沖擊而產生振動。先導式溢流閥的導閥口和主閥口，油液流速和壓力的變化很大，很容易出現空穴現象，由此而產生噪聲和振動。

The noise generated when the hole due to various reasons, the air is sucked into the oil, or lower than the atmospheric pressure in the oil pressure, dissolved in the oil in the air will precipitate the formation of bubbles, the bubbles in the low pressure area is larger, when the oil flow to the high pressure area, is compressed, the volume suddenly become smaller or on the other hand, the bubble disappeared; as in the high pressure area was smaller when the volume, flow to the low pressure area, the volume suddenly increased, the oil bubble volume this rapid change phenomenon. Sudden change of bubble volume will produce noise, and because this process occurs in an instant, the impact will cause the local hydraulic vibration of the pilot valve port. Pilot type relief valve and the main valve port, the oil flow rate and pressure changes greatly, it is prone to cavitation, resulting in noise and vibration.

現貨東京計器TOKIMEC換向閥DG4V-3-2A-U-H-100

東京計器主要是用于沖壓機，通過電動機驅動飛輪，并通過離合器，傳動齒輪帶動曲柄連桿機構使滑塊

沖壓機

上下運動，帶動拉伸模具對鋼板成型。所謂的雙動就是指壓力機有兩個滑塊，分為內滑塊和外滑塊，內滑塊帶動模具的凸模或凹模，外滑塊帶動模具上的壓邊圈，在拉伸時壓邊圈首先動作壓住鋼板邊緣，內滑塊再動作進行拉伸。

設計原理是將圓周運動轉換為直線運動，由主電動機出力，帶動飛輪，經離合器帶動齒輪、曲軸（或偏心齒輪）、連桿等運轉，來達成滑塊的直線運動，從主電動機到連桿的運動為圓周運動。

連桿和滑塊之間需有圓周運動和直線運動的轉接點，其設計上大致有兩種機構，一種為球型，一種為銷型（圓柱型） ，經由這個機構將圓周運動轉換成滑塊的直線運動。沖壓機對材料施以壓力，使其塑性變形，而得到所要求的形狀與精度，因此必須配合一組模具（分上模與下模），將材料置于其間，由機器施加壓力，使其變形，加工時施加于材料之力所造成之反作用力，由沖壓機機械本體所吸收。